12V/24V Solar Panel Battery Charger Charging Controller Regulator

10A / 20A / 30A / 40A / 60A PWM Solar Panel Battery Regulator Charge Controller 12V or 24V Batteries with Dual USB Output - Blue Case

This PWM Solar Battery Charge Controller automatically manages and regulates the voltage and current to the battery from the solar panel(s). It incorporates short-circuit, open-circuit, reverse polarity, and overload protection in order to ensure that the batteries are not overcharged and that power isn't discharged from the batteries to the solar panels during shaded or dark conditions and drain the batteries. It comes with USB ports to charge your phone and other electronic devices directly from the controller.

This solar charge controller is perfect for smaller home, cabin, RV and other remote and portable solar systems.

Features

• This controller is designed for use only with 12V and 24V lead-acid batteries. It cannot be used with lithium-ion, nickel-cadmium or other battery types.
• Regulates the voltage from the solar panels going to the batteries.
• Built-in industrial master chip to control the charge and discharge process with adjustable parameters to prolong the battery life cycle and stabilize power to the load.
• 3-stage PWM charge management with short-circuit protection, open-circuit protection, and reverse polarity protection.
• Dual USB outputs with 5V/2A maximum power (across both outputs) can charge mobile phones, tablets, and other USB-powered devices.
• LCD display with backlight function displays status and parameters.
• Dual MOSFET reverse current protection, low power dissipation.
• Easy to install and operate, suitable for home, industrial, commercial, remote and portable solar energy systems.
• Models for 10A, 20A, 30A, 40A and 60A maximum input current

Specifications

-Size: Approx. 13.3 x 7 x 3.5 cm/ 5.24 x 2.76 x 1.38 inch (LxWxH) (10A, 20A and 30A models)

-Approx. 18.8 x 9 x 4.7 cm/ 7.4 x 3.54 x 1.85 inch (LxWxH) (40A & 60A models)

-Battery Voltage: 12V/ 24V (Auto recognition)

-Input Charging Current: 10A / 20A / 30A / 40A / 60A dependent upon the model chosen. The maximum panel output current should be about 25% less than the controller's maximum input current rating. For example, with a single 6A 100W panel, use the 10A model. Two 6A panels (12A total) should use the 20A model. If in doubt, use the higher current model, i.e. if the maximum panel output current is 9A, use the 20A model rather than the 10A model. 

-Maximum Discharge Current: 10A (10A, 20A and 30A models)

• 20A (40A model)
• 30A (60A model)

-Internal power consumption: =10mA

-Over Charge Protection:

• B01 Sealed: 14.4V/28.8V
• B02 Gel: 14.2V/28.4V
• B03 Flood: 14.6V/29.2V

-Over Charge Float: 13.7V/27.4V

-Charge Recovery Voltage: 12.6V/25.2V

-Over-discharge Protection: 10.7V/21.4V

-Over-discharge Recovery: 12.6V/25.2V

-USB output: 5V/2A

-12V batteries should be used with solar panels capable of generating 18V-25V 

With 12V batteries, the maximum panel voltage must not exceed 25V

-24V batteries should be used with solar panels capable of generating 36V-50V 

With 24V batteries, the maximum panel voltage must not exceed 50V

-Maximum Power Input:​

• 10A Model 12V: 120W (MAX),  24V: 240W (MAX)
• 20A Model 12V: 240W (MAX),  24V: 480W (MAX)
• 30A Model 12V: 360W (MAX),  24V: 720W (MAX)
• 40A Model 12V: 520W (MAX), 24V: 1040W (MAX)
• 60A Model 12V: 780W (MAX), 24V: 1560W (MAX)

-Operating Temperature: -35 ~ +60C

-Storage Temperature: -35 ~ +60C

Package Includes:
1X (1 Piece) 10A, 20A, 30A, 40A or 60A PWM Solar Charge Controller

NOTE: The solar panel and battery in the photo are shown to illustrate the controller's interconnections only. They are not included with the charge controller